Say hello to our new Bumblebee 914! So first off what the heck is a Can Am or Limited Edition (LE) car?

Karl Schulz's LE Creamsicle from our Customer Car Story in May.

Haltbar™ Resins Program

 

 

Upholstery Clips in Your Seats

Sometimes when we make a new part it can be hard to see the usefulness of it until you are mid-restoration and need one. The seat upholstery clips are one of these parts.

If you have ever disassembled your seat you will notice that there are a bunch of single prong clips underneath the seat cushion.

These clips also run along the inner edges of the seat center section all the way up to the base of the headrest. These pointed clips are the basis of how the seat goes together and help the vinyl retain its shape.

There are 23 clips in total - 19 single prong clips along with 2 medium and 2 large double clips. These double clips do more than just secure the vinyl to the chair, they are actually mounting points that secure the seat rails to the seat bucket.

The Problem

Rust is one of the biggest problems that the 914 faces, and the seats are not immune to this. It is not uncommon for a bolt to break off while trying to remove the seat rails from the seat. This is a crucial step you must take in order to replace the seat back bolster vinyl, which is notorious for splitting from age and wear. If you want to avoid the headache of dealing with snapped bolts, look for the back side of the clip and soak it with parts blaster. This can be seen once you remove the inside edge of the vinyl and lift up the foam padding.

Also, if your clips have been reworked before they can easily fatigue which may lead to the prong snapping off. Prior to developing these I could not find these commercially available anywhere. I searched upholstery shops to see what they had to no avail. I did come across a few people that could MacGyver a clip out of carpet tack strip material but it was not the ideal solution.

Seat Disassembly

After removing the seat cushion/center section, if you stretch the inner edges of the vinyl down you can pull the bottom edge away from the clips. after freeing the inner surface, you will need to take the 2 screws on the back of the headrest out. This will allow the vinyl flap to come down and also reveal the 2 screws that hold the headrest to the fiberglass body of the seat.

Once the vinyl is off the seat you can get a better view of the clips. They attach to the seat using a pop rivet so removal and reattachment are pretty straight forward. Do note that sometimes the fiberglass attachment point may have some damage. Do not worry you find this on your seat, just use a small washer as a backer for the pop rivet so it has a stronger surface to attach the clips to.

The exact location of the clips is mostly relative to each seat with the exception of the double clips. You will want to use the seat rails as a guide to assure they all line up correctly.

About The Parts We Made

Currently, we are only selling these in kits per seat. We will be selling individual pieces in the future, so if you need just a single part they will be available soon. We have put the kits together with all the pop rivets you need to attach the kit. The kits will be significantly less expensive than buying individual parts, but if you just need one piece I get it. This option will become available in the next few weeks. We also have the new hardware kit with freshly plated bolts and washers that will be listed separately shortly, but is included in the kit too.

I have done a seat or two myself and they are not particularly difficult to complete, but do require time and patience as they are deceptively simple.

Our good friend Ian Karr has just done a video showing the disassembly side of it in part 1 of his seat reupholstery series. These will be an excellent primer for you if you choose to take this on. I would encourage all to check out his 914 repair adventures and allow him to be your Sherpa on the restoration journey.

I again want to thank everyone for their support during these troubling times as it allows us to continue making parts like these.

Sincerely,

Mark Whitesell

AKA Mikey914 on world

I wanted to touch on 2 subjects for this newsletter to shed some light on what is really going on behind the scenes of our Interior program and the 914 Resins program.



Interiors



As many of you may or may not be aware, we started making door panels almost 7 years ago. We had backed off on production of these due to the amount of labor they took to construct and the need to harvest some of the existing hardware from the old door panels. I am pleased to announce this is no longer the case.

 

We now fabricate this hardware and it comes standard with all of our door panels, including the cage nuts. We have also included all 18 door panel clips needed to mount the new panels to the door frame.



Note that the holes necessary for mounting the door pockets and pull handles now come pre die-cut. These are also shipped with the door cups to make this ready to install out of the box. Our goal is to make installation as painless as possible. 

We are currently building up some back stock and will be relaunching these in the coming months. The new listing will also have a few “custom” options that will include plaid, houndstooth, and even GT door pulls. We had to slow down on production to get these back on line in a manner that yields a better product.



We have also just completed the upholstery mounting clip sets for the seats. These are critical for making the seat side bolsters and center sections stay in place. In most cases, many of these are completely rusted away or missing as they were never available directly from the factory for replacement.

These will be sold as a set per seat basis and will include the pop rivets necessary to mount the clips.



We are committed to providing you with what you need to make your car look good. We look forward to sharing more information about future items that will be available in this category soon.



Resins



We had the opportunity to mount the complete trunk assemblies for both the front and rear trunks lids. The front trunk springs really have more pressure than they need to open the hoods so we are actively sourcing a better option for use with the resin hoods.

 

Fitment is looking good currently but we are making some adjustments to the metal that gets embedded into the hoods to give them more strength.

 

The front hood with headlight delete should be ready this before August, the alignment is good and only needs some minor changes. A few of the molds have some imperfections in them that are minor, but keep them from being 100% perfect and ready to start using. There are some “hot spots” in the molds that will require glazing putty and some block sanding to remove. They are minor, but we believe in full disclosure. We are looking at the costs to finish them completely in house as an option.



Finally, we will also have replacement front valances available this month. The steel ones are hard to come by, so if yours is undamaged why risk it? 



Stay well and try to get in some quality 914 time, 'tis the season.



 Remembering Roxie

I’m sad to report that my faithful friend and frequent shop dog Roxie passed away this past Wednesday. She was with us for over 14 years, just last week we were commenting that she may have a few more years left with us because she seemed so healthy.

I'm glad she got to spend one last brisket filled holiday with the extended family this past 4th of July. We already miss you girl.